Bush Gang CartelService & Creative Hub · Holly Hill, SC

Real shop work.
Honest diagnostics.
No staged stuff.

Mowers, small engines, generators, cars, welding, and creative work — done out of Holly Hill, South Carolina by a veteran-owned, blue-collar shop that tells you straight what's wrong and what it'll take to fix it.

Open 6am–9pm · field hours vary 681 Fourwind Road, Holly Hill, SC Booking subject to review
Mechanic wrenching on the engine of a riding mower inside the shop
Riding mowers torn down, diagnosed, and fixed right — that's the work.
Welding helmet and worn work gloves on the shop bench, with the open shop door looking out onto green woods
The work before the post. Helmet down, gloves off — the bench at the end of the day, shop door open to the woods.

Services, detailed out

No bare lists here. Every service below is broken down the way it'd be written on an estimate — what the job covers, what's included, and what costs extra. Parts are priced at what they cost; labor is quoted before work starts, not after.

1

Mowers & Small Engines

Riding mowers, push mowers, zero-turns, generators, pressure washers, and other small-engine equipment. If it runs on a little gas engine, it belongs on this bench.

Full tune-up includes

  • Oil change — drained, refilled to spec
  • New spark plug, gapped correctly
  • Air filter cleaned or replaced
  • Fuel filter replaced where fitted
  • Blade sharpened & balanced (mowers)
  • Deck scraped out and buildup removed
  • Belts & cables inspected for wear and stretch
  • Battery load-tested, terminals cleaned (riders)
  • Tire pressure set, deck leveled (riders)
  • Full run test under load before it leaves

Repair work covers

  • Carburetor work — cleaning, rebuild, or replacement
  • No-start diagnostics — spark, fuel, compression, in that order
  • Belts — drive belts and deck belts replaced & routed right
  • Blades — replacement, spindles, mandrels
  • Starter & charging — solenoids, starters, batteries
  • Fuel system — lines, tanks flushed, stale-fuel cleanup
  • Generator service — tune-ups, carb work, output checks
  • Cables & controls — throttle, choke, drive cables

Tune-up vs. repair — the difference

A tune-up is maintenance on a machine that already runs: fluids, plug, filters, blade, and a full inspection so small problems get caught early. It's a set job at a set scope.

 

A repair starts with a machine that's down. It begins with diagnostics to find the actual failure — then you approve the fix and the price before any part gets ordered or any wrench turns on the repair itself.

Straight talk: if a repair is going to cost more than the machine is worth, you'll hear that from us before you spend a dime on it.

2

Cars — Maintenance & Diagnostics

Keeping daily drivers on the road: routine maintenance, honest code reading, light repair, and paint prep work.

Maintenance includes

  • Oil & filter changes — correct weight, correct filter
  • Fluids checked & topped — coolant, brake, transmission, washer
  • Air & cabin filters inspected and replaced as needed
  • Battery tested, terminals cleaned and protected
  • Belts & hoses inspected for cracks and wear
  • Tires — pressure set, wear pattern read
  • Lights & wipers checked all the way around

Diagnostics & light repair

  • OBD-II scan — codes pulled and explained in plain English
  • Live-data checks to confirm a code before parts get bought
  • Sensors & bolt-on parts replaced as diagnosed
  • Paint & prep work — sanding, masking, priming, panel prep
  • Light repair — quoted by the job after a look

How diagnostics work here: a code tells you where to look, not what to replace. We confirm the failure first — that habit saves you from paying for parts your car never needed.

3

Welding, Assembly & Property Work

The hands-on work other shops won't take. Labor is priced by the job — you get the number up front, based on what the work actually is.

By the jobLabor quoted up front

Welding & metal work

  • Light welding — brackets, frames, mower decks, trailer repairs
  • Cracked & broken metal assessed honestly before burning rod
  • Grinding & cleanup included on every weld job

Assembly, handyman & yard

  • Equipment assembly — sheds, implements, furniture, kits
  • Handyman work — small fixes around the house & shop
  • Yard work & property labor — clearing, hauling, cleanup
  • General labor — if it takes tools and sweat, ask
Welder in a protective mask welding steel, sparks flying
4

Creative Work — Websites, Ads & Flyers

The same shop builds the stuff that gets other small businesses seen. Built by somebody who runs a small business himself — priced for people who work for a living.

What you bring

  • The facts — services, prices, photos, contact info
  • Your logo if you have one — if not, a clean type treatment gets made
  • Examples of looks you like, if you've got any

How it works

  • Scope & price agreed before the build starts
  • Draft shown to you for corrections before it goes live
  • Files delivered — print-ready and web-ready versions

Start a creative job the same way as any other: call or text 803-496-6241 or email bushgangcartel@gmail.com with what you need made.

Find the label before you call

The model and serial numbers are how parts get ordered right the first time. Find your machine below, check where its label hides, and have those numbers ready when you call or text — it speeds everything up.

Riding Mower

Where to look: under the seat — flip it up and check the frame rail or the underside of the seat pan. Also check the rear frame near the hitch plate.

  • Bring: model & serial off the mower tag
  • Engine numbers are separate — stamped on the valve cover or blower housing
  • A photo of the tag works fine

Push Mower

Where to look: on the rear of the deck near the discharge chute or back wheels, and on the engine itself — usually stamped into the blower housing or on a tag above the spark plug.

  • Bring: deck model/serial and engine model/type/code
  • Engine code matters — it pins down the exact parts
  • Deck size (inches) helps too

Weed Eater / Trimmer

Where to look: on the engine housing near the starter cover, or on a sticker wrapped around the shaft. Handheld blowers and chainsaws hide theirs near the fuel cap or handle.

  • Bring: brand, model & serial
  • Say whether it's 2-stroke or 4-stroke
  • What it does (or won't do) when you pull the cord

Golf Cart

Where to look: depends on brand — common spots are under the seat on the frame, in the glove box area, on the frame rail behind the batteries, or on a plate near the floorboard.

  • Bring: brand, model & serial
  • Gas or electric — and battery voltage if electric
  • Year if you know it

Four-Wheeler / ATV

Where to look: the VIN is stamped on the frame — usually on the front frame rail behind the bumper, or on the left frame rail near the footwell. Engine numbers sit on a pad on the engine case.

  • Bring: the full 17-digit VIN
  • The 10th character of the VIN gives the year
  • A rubbing or clear photo of the stamp helps if it's rusty

Motorcycle

Where to look: the VIN is stamped on the steering head — turn the bars and check the right side of the neck. There's often a matching sticker on the frame nearby, plus engine numbers on the case.

  • Bring: the full 17-digit VIN
  • Make, model & year if you have paperwork
  • What it's doing — no-start, running rough, electrical

Free info — fix it yourself first

Plenty of "broken" machines just need ten minutes and the right check. Run through these before you spend money — and if it still won't go, that's what the shop is for.

Fuel

It ran last year, won't start now? Suspect the gas.

Old ethanol fuel is the #1 cause of no-starts after a machine sits. Drain the tank and carb bowl, refill with fresh fuel (ethanol-free if you can get it), and try again before you buy a single part. Fuel left over winter turns to varnish and plugs the tiny jets in the carb.

Spark

The two-minute spark test

Pull the plug, reconnect the wire, ground the plug body against the engine block, and pull the cord (or crank it). You want a strong blue spark. No spark points at the plug, the kill switch, or the ignition coil — in that order of price.

Blades

Sharpen right, cut right

A dull blade tears grass instead of cutting it, and torn grass browns and invites disease. Keep the factory bevel angle, take the same amount off both ends, and check balance on a nail — a blade that hangs level is balanced; one that dips needs a little more off the heavy end.

Air

A choked filter acts like a bad carb

Before you blame the carburetor, pull the air filter. A filter caked with dust and oil starves the engine and makes it surge and stall exactly like a fuel problem. Paper filters get replaced; foam filters get washed, dried, and lightly oiled.

Battery

Clicks but won't crank?

Clean the terminals first — corrosion you can barely see can stop a starter cold. Then check the battery with a meter: around 12.6 volts resting is healthy. If it drops hard under load, the battery is done no matter what the charger says.

Storage

Put it away right, start it in spring

End of season: run the machine with fuel stabilizer, then either drain the carb bowl or run it dry. Pull the battery and keep it somewhere it won't freeze. Ten minutes in the fall saves a carb job in March.

Videos & one-on-one advice

The shop knowledge, packaged. Full repair courses and direct mechanic advice are in the works — get on the list now and you'll be first to know when they open.

Get on the list

Tell us what you're interested in. Sending opens your email app with the message filled in — addressed to bushgangcartel@gmail.com.

Your email app should open with everything filled in. If it didn't, email bushgangcartel@gmail.com directly.

About the shop

A mechanic working on a zero-turn mower surrounded by small engine equipment

Timothy Windham — Owner

Veteran-Owned Blue-Collar Built Community Minded

Veteran. Former firefighter. Small-engine mechanic. Timothy Windham built Bush Gang Cartel the way he was taught to work: show up, diagnose it honestly, fix it right, and charge a fair price for it.

The shop handles the work regular folks actually need — the mower that won't start in April, the generator that has to run when the power's out, the daily driver with a light on the dash, the fence bracket that needs a weld. Service first, sales never.

The name has a history: Bush Gang Cartel started in DayZ, the survival game Timothy played and streamed — the crew that ran the treelines together. The game turned into a brand, and the brand grew into this business. The field mindset came with it: know your gear, fix what breaks, look out for your people.

You can also find the shop's real repair work — no staged stuff — on TikTok and Facebook.

Book a job

Two ways in: reach out direct, or send the facts first so the job can be looked over. Either way, have your machine's model and serial numbers handy if you've got them.

Call or text

Fastest way to reach the shop. If it goes to voicemail, leave the machine and the problem — you'll get a call back.

803-496-6241
  • Hours: 6am–9pm
  • Field hours vary — leave a message after hours
  • Text a photo of the machine and its label tag

Email the facts

Send what you've got and the job gets reviewed before a time is set.

bushgangcartel@gmail.com
  • Machine & brand, model & serial numbers
  • What it's doing (or not doing)
  • Photos of the machine and the problem
  • Where the machine is, and your phone number

Booking is subject to review — every job gets looked at first so the right time, tools, and parts are lined up before you haul anything over.

Shop address: 681 Fourwind Road, Holly Hill, SC 29059

Call the shop Book a job